Serpent Viper 990 1/8 Nitro On-Road Car

Serpent Viper 990 1/8 Nitro On-Road Car

Serpent Viper 990 1/8 Nitro On-Road Car Serpent Viper 990 1/8 Nitro On-Road Car Serpent Viper 990 1/8 Nitro On-Road Car

From Serpent:
We have spent a lot of testing and research to improve the 989 platform. We put a lot of emphasis on the flex characteristic since that showed very promising results.

On top of that we improved weight, weight distribution and ease of maintenance.

Beside all these new features we kept 90% of our proven transmission and our excellent shock absorbers.

New key features

The ultra-narrow chassis is milled down to allow the lower radio plate as well as improved flex. keeps the improved flex characteristics. The central hole underneath the tank is narrower, as a consequence of the narrower chassis.

The central weight bridge is now mounted from underneath and allows for a quick change of the weight.

The weight itself is now fixed using a nylock nut. Bulletproof!

The front weight bridge is now also mounted from the bottom to allow easy access to the weight.

Also, the front weight is now adjustable from the bottom.

There are 2 additional locations to put a small weight, just behind the servo-saver and in front of the engine.

The engine has been lowered 1mm for improved flex as well to lower the CG.

The rear of the chassis has a slot. This will be explained later here. It has to do with adjustable flex. It also carries 2 steel countersunk screws that act as a counterpart of the down-stop screws. This helps to keep the down-stop more accurate and consistent.

Talking about flex: we tested a lot and one of the improvements came from lowering the radio plate by 2.5mm. We also change the shape of it.

The front of the car can be adjusted to more flex by removing the front stiffener bracket.

An even softer option would be to remove the 2 front screws.

The rear of the car is also adjustable regarding the flex. To regular rear end features the proven, one-piece rear plate.

As an option it is also possible to use a softer rear end using an optional 2-piece rear plate.

The radio-box is completely new. The “backbone” of it is a carbon plate and an aluminum frame.

The aluminum servo mounts are eccentric and can be mounted in 2 ways to adjust them to the brand of servos.

The receiver box is more spacious than the one used in our 988, still it is very compact. It provides enough space even for older type receivers plus the transponder.

This new box is mounted to the radio plate in a flexible way in order to not influence the flex of the car.

The extending arm of the frame helps to keep the radio box in the desired position without influencing flex.

The rear end is completely new. It features a new design to allow a re-active toe-change as well as avoid any binding at all!

By changing the position of the link, the amount of toe-gain under compression can be adjusted. The position shown is the “neutral” position.

Since the upper link is replaced by a suspension arm, we also changed the upper pivot on the upright. It is now super easy to adjust the correct camber.

The height of the pivot ball is adjustable by changing the aluminum insert. There are 3 positions.

The upright carries an aluminum insert where the ball bearings of the wheel axle sit. In that way we can achieve the perfect roundness even under load to achieve the least friction of the transmission possible.

In this way it is also really easy to remove the wheel axle/driveshaft for maintenance.

The front steering-block features a similar construction. The aluminum insert gives the same advantages as in the rear with improved drive train effectivity and improved ease of maintenance.

But because this insert is eccentric, it is also possible to change the roll-center as well as using a trailing or leading set-up.

Of course, the steering-blocks are still left/right symmetrical and can be used with option1 as well as option2 levers.

The front upper suspension bracket now has an improved design takes provides a better placement to avoid camber or caster irregularities by using bushings.

The new lighter 2-speed shaft is 10g (!) lighter and features a super-true e mounting of the 18t pulley adapter.

General features

7075 T6 aluminum 5mm chassis plate

The 5mm aluminum chassis has perfect symmetrical shape for even flex and weight distribution. The ultra-narrow chassis is very light, while it still remains strong in critical places.

The wire type front anti-roll bar is ball raced. It is easy to change and adjust due to the open front-end design. The standard wire is 2.5mm and 2 optional thicknesses are available. The pivot ball link system directs the suspension movement to the bar and allows easy tweak adjustment.

The steering blocks are connected to the arms with spring steel 8.5mm pivot balls, which run very smooth and well protected in nylon cups and are easy to adjust with a 2.5 hex tool.

The long durable front lower wishbones are the open-style arms similar to the 977. An aluminum shock mount plate is screwed onto the lower wishbone. This allows the shock attachment point to be placed further outwards improving shock motion. The front lower arms are mounted to the front brackets with nylon holders. The kit includes 2 versions: in and out. This system also enables quick and easy front drive shaft maintenance.

Of course, the 988 closed arms are usable as well.

The left and right interchangeable upper arms are mounted with 3 position nylon suspension pin inserts. The 3 position inserts allow camber-change adjustments and are held in place by the anodized aluminum top brackets. Below the top brackets, spacers can be used to change their angle or height. Caster is adjusted with clips on the upper pivot pins. The same clips are also used on the lower pivot pins to change wheelbase.

The black anodized aluminum front axle has Japan made one-way bearings. Spring steel drive cups connect to the long and thin spring-steel drive shafts with CVD system. The ball raced spring steel wheel axles have aluminum quick-change levers. The open front-end design allows for very fast and easy removal of the front axle and drive line parts.

The central mounted servo saver allows easy and fast Ackermann adjustment. The servo saver features a top mounted insert which can be used in 3 positions. Another 2 Ackermann positions are available on the steering blocks.

The rear end construction with aluminum brackets is a very open design, which allows for easy of maintenance and cleaning. Dis-assembly requires the removal of only a few screws. Replacing a belt if needed, is a simple task. The eccentric bearing holders on the rear shaft allow adjustment of belt tension. The whole rear end can be removed as one unit from the chassis by removal of only a few screws.

The wire type rear anti-roll bar is ball raced. It is mounted in the rear bearing blocks and is easy to change and adjust. The standard wire is 2.5mm and 2 optional thicknesses are available. The pivot ball link system directs the suspension movement to the bar and allows easy tweak adjustment.

The narrow solid rear axle in Serpent spring steel has a lightweight 9mm wide 48T pulley. The axle has a double slot for the driveshaft pin for lightness and long life. Spring steel, CVD type, drive shafts connect the rear shaft to spring steel wheel-axles with aluminum quick-change levers. A very durable and long-lasting drive train.

The rear floating body mount which is mounted on the up-rights with 2 arms is centered by a carbon-fiber and steel guider. The mount has 4 positions on each side to choose from, depending on body shell used and traction available. The threaded holes on the end of the body mount give the option to add further body-supports.

Optionals

A large selection of optional parts is available to improve performance, speed, weight and looks even further.

#903020
Visit Serpent.com
See more posts about Serpent

Serpent Viper 990 1/8 Nitro On-Road Car Serpent Viper 990 1/8 Nitro On-Road Car Serpent Viper 990 1/8 Nitro On-Road Car Serpent Viper 990 1/8 Nitro On-Road Car Serpent Viper 990 1/8 Nitro On-Road Car Serpent Viper 990 1/8 Nitro On-Road Car Serpent Viper 990 1/8 Nitro On-Road Car

Never miss an issue of RC Car Action!

Subscribe today with a Digital Edition subscription or Print + Digital combo!

Updated: April 19, 2022 — 11:30 PM

Leave a Reply

Your email address will not be published. Required fields are marked *

Air Age Media © 2022