Serpent Cobra GT 3.0 1/8 4wd Nitro On-Road Car

Serpent Cobra GT 3.0 1/8 4wd Nitro On-Road Car

Serpent Cobra GT 3.0 1_8 4wd Nitro On-Road Car (11) Serpent Cobra GT 3.0 1_8 4wd Nitro On-Road Car (3) Serpent Cobra GT 3.0 1_8 4wd Nitro On-Road Car (4)

From Serpent:

The Serpent Cobra GT is the most popular brand in GT racing and its performance is proven by many big race wins in the highly competitive race scene for GT’s in America. The Cobra GT 3.0 is the latest development stage of the Cobra GT platform, which is running successfully for over 5 years with very small changes only. Below we show the key updates to the GT to continue its strong performance and famous durability.

The Cobra GT is a combined design effort by Billy Easton and Michael Salven, in cooperation with our USA team-drivers Desoto and Morganti.

Main new features:

  • New XLi superlight 2-speed gearbox
  • New aluminum middle bearing blocks ( holding brake and 2-speed)
  • New front and front rear aluminum suspension holders
  • New Alu c-hubs in 6 degree version
  • New aluminum, uprights for new rear geometry
  • New alu shock absorber risers front and rear
  • New 4.5mm carbon shock towers front and rear

Explaining the new features

New XLi superlight 2-speed gearbox

The XLi gearbox comes from the Viper 977-Evo kit and is well proven for performance and durability, as well as ease of setting. The lower inertia will make you accelerate faster.

New aluminum middle bearing blocks ( holding brake and 2-speed)

To hold the new 2-speed gearbox/shaft as well as the existing double brake system newly designed superlight aluminum bearing blocks are designed.

New front and front rear aluminum suspension holders

These are designed to change the pivot pin angle, so the lower wishbones will be more straight, which geometry suits on road racing better.

New Alu c-hubs in 6 degree version

The new alu c-hubs are needed to make maximum use of the new pivot pin / wishbone angle. CNC-machined from 7075 T6 aluminum, laser engraved and black anodized units.

New aluminum, uprights for new rear geometry

To allow a better onboard geometry we designed these new CNC machined aluminum uprights, black anodized and laser engraved.

  • New alu shock absorber risers front and rear
  • New alu shock towers front and rear

The durable machined alu shock-risers front and rear allow for a more on road aimed angle of the shock absorber creating more overall grip and more predictable cornering. The new 4.5mm lower carbon fiber shock towers also accommodate the new shock angles, with a choice of 5 holes for further fine-tuning.

New aluminum middle bearing blocks ( holding brake and 2-speed)

To hold the new 2-speed gearbox/shaft as well as the existing double brake system newly designed superlight aluminum bearing blocks are designed.

New front and front rear aluminum suspension holders

These are designed to change the pivot pin angle, so the lower wishbones will be more straight, which geometry suits on road racing better.

New Alu c-hubs in 6 degree version

The new alu c-hubs are needed to make maximum use of the new pivot pin / wishbone angle. CNC-machined from 7075 T6 aluminum, laser engraved and black anodized units.

New aluminum, uprights for new rear geometry

To allow a better onboard geometry we designed these new CNC machined aluminum uprights, black anodized and laser engraved.

Overall features / specs

Chassis plate

Chassis plate in 3mm 7075 T6 aluminum , with machined pockets to create flex and or make lighter. Kick-up angle on front as need due to the race-rules. Countersunk holes. Slots to locate the front and rear suspension mounts precisely. Angled sides to increase stiffness. Open pockets to access flywheel and 2-speed gearbox. Laser engraved Cobra GT logo.

Bumper

Captured foam bumper set, with wide foam bumper and strong upper and lower bumper-plate.

Chassis stiffeners

Composite stiffener front and rear, to give extra stiffness, but still allow some flex as needed.

Central disk brake system

Very low and centrally placed brake system for low center of gravity with ventilated glass fiber brake disks, combined with thick steel plates which won’t bend under pressure.

Radio-box

Composite radio box which offers space for the lay-down steering servo and the upright placed brake-throttle servo. Sufficient spacers are supplied for correct fitting of the servo’s. The receiver and battery can be placed safely under the large cap. The transponder can be mounted in the central part, between servo and receiver box. The whole assembly including linkages can be taken off easily and fast in one go, when cleaning the car, or doing maintenance.

Servo arms and linkages

The servo arms have a splined insert to have the right fit per brand. The linkages runs very clean and tight and are easy to access to modify settings.

Suspension brackets

Beautifully machined 7075 T6 suspension brackets in anodized, laser engraved. Precision fit for the nylon roll center inserts and pivot balls / pins. The GT 3.0 front suspension brackets make the pivot-pin and lower arm more horizontal, which improves handling and steering.

Steering blocks assembly

Composite steering blocks combined with 10 dgr C-hubs for precise steering. Spring steel wheel-axles with large size bearings 8x18x5 and 15x21x4    with precision threaded aluminum wheel-hubs with +3 offset. Flanged wheel nuts to guarantee that you will not lose a wheel nut in a race.

Front suspension

Durable oversized lower suspension arms in strong composite nylon. On the lower side the special down stops screws are mounted. The lower shock-mounting pins are secured with a small grubscrew from the bottom.

Front anti-roll bar

The ball raced front anti-roll bar system, consist of a spring steel bend wire, which is guided through the diff-cases and run in ball raced steel adaptors. The wire is linked to the lower suspension arm, with a captured adjustable threaded pivot ball, for very precise and low friction operation.

Shock tower and body mounts front / alu shock-risers

new 4.5mm thick carbon shock tower with 5 upper positioning holes for the shocks and 6 holes for roll-center positions. 1 centrally located adjustable body mount , and 2 forward mounted adjustable body mounts, all with flip-tops.  The durable machined alu shock-risers in front allow for a more on road aimed angle of the shock absorber creating more overall grip and more predictable cornering.

Angled steering system / servo saver

The bell cranks are angled to reduce the angle of difference between the total caster and steering plane. Therefore you will have less bump steer and a truer steering Ackerman through the entire range of suspension

Ackermann plates

With the design of the steering bell cranks when changing the Ackermann you will not need to adjust your steering tie rods. You simply will only need to adjust your end points on your radio..

Rear suspension arms

Durable oversized lower suspension arms in strong composite nylon. On the lower side the special down stops screws are mounted. The lower shock-mounting pins are secured with a small grubscrew from the bottom.

Rear uprights assembly

New aluminum, black anodized and laser engraved uprights with 3 upper roll-center positions. Strong steel track-rods with L/R threading and strong ball joints to pre-set camber. Spring steel wheel-axles with large size bearings 8x16x5 and 13x19x4 with precision threaded aluminum wheel-hubs with +3 offset . Rubber dustcovers in the rear to protect the cvd system and keep the lubrication inside. Flanged wheel nuts to guarantee that you will not lose a wheel nut in a race.

Rear anti-roll bar

The ball raced front anti-roll bar system, consist of a spring steel bend wire, which is guided through the diff-cases and runs in ball raced steel adaptors. The wire is linked to the lower suspension arm, with a captured adjustable threaded pivot ball, for very precise and low friction operation.

Shock tower rear / alu shock-risers

New 4.5mm thick carbon shock tower, integrated into the rear section for extra stiffness, with 5 upper positioning holes for the shocks and 6 holes for roll-center positions.   The durable machined alu shock-risers in the rear allow for a more on road aimed angle of the shock absorber creating more overall grip and more predictable cornering.

Wing mount and body mounts rear

Composite rear wing, with strong nylon adjustable rear body mounts on wide body-support bridge located far enough to the rear, to support the bodies in best way.

Captured pivot pins and balls and bolted hinge pins

All spring-steel hinge pins are either captured or bolted in place and made in spring-steel quality. This insures your chances to finish an hour long main event, while battling for the lead. This relieves stress on the hinge pin when adjusting the kick up, or anti squat. Your pin is free to rotate to any angle without binding.

Shock absorbers big-bore 16mm

Hard Teflon coated threaded shock bodies with 4mm shock-rods. Black anodized aluminum screw on shock-tops with Serpent laser engraving.  Pre-load adjusters with O-rings inside. Shocks use large diameter membranes and large diameter O-rings and bushings to create a super smooth and leak-proof package. Large diameter pistons are held in place by a nut on the polished shock-rods tops. Open type spring retainer to let dirt out easy.

RCM shock springs

Short type color-coded shock springs are supplied for the 1st standard set-up Springs are grinded flat top and bottom, and checked individually for tension and length.

Compact gear differentials

Very compact gear differentials with very smooth metal sintered gears, and steel shaft. Perfect sealing case with special gasket and O-rings. Very light and durable outdrive cups in spring-steel.  Hardened spring-steel diff-coupler 13T with connector running in 2 oversized bearings 8x19x6 and ballbearing-13x19x4.

Front and rear cvd-sets

Both front and rear captured driveshafts are being used with CVD system. Durable yet light spring steel engraved driveshafts with hard steel pins.

Spring steel transmission parts

The front and rear thin but strong spring steel cardan shafts connect the differentials with the gearbox section.

Engine mount

Machined 7075 T6 aluminum engine mounts with side cooling fins.

Coil exhaust wire and alu mount

The tuned pipe is securely fastened with the cols spring and aluminum holder.
Helps aid in the front to back movement of the pipe when chassis flex occurs. Helps to prevent damage to your exhaust gaskets.

SL8 XLi 2-speed gearbox

SL8 gearbox comes straight from the Serpent 977-EVO 1/8 scale on road car. Very light and compact design. Centrifugal spring loaded shoe system with small alu bell and flange with one-way bearing.  Durable composite 2-speed gears with smaller pitch .

2-speed clutch-housing with screw-on gears

Strong steel clutch-housing with precision machined threading, with hard coated aluminum screw on gears with smaller pitch .

4-shoe clutch

Full carbon 4 shoe clutch-set with medium type springs. Easy to assemble with light and durable anodized aluminum flywheel.

150cc fuel tank

Composite nylon fuel-tank with super sealing spring-loaded shock-cap, bronze sintered clunk type filter and splash-side guard. Side features slots to mount the supplied tube-guiders. Tank mounts to chassis on longer composite posts with integrated rubber buffers to allow some movement and reduce fuel-foaming. The clunk system will allow the engine to continue running when the car is up-side-down.

Oils and grease

The shock-oil, diff oil and some grease is supplied to meet the standard set-up.

Manual and set-up

Full color online manual and USB stick version with easy to follow assembly steps, exploded views for easy spares ordering, a blank and standard set-up sheet for a good start set-up.

Decals

Black and white promo body-decals ; Serpent generic and Cobra GT ones.

Packing

Parts are packed according to the steps explained in the manual.

Service and Support

The Serpent distributor, dealer or agent is your source for more info, but also the Serpent website, Facebook-sites and the YouTube channel provides lots of information.

Needed to complete the car:

  • radio and receiver
  • rx battery pack
  • engine and pipe system
  • foam on road air filter or off-road type
  • wheels and tires
  • body and wing
  • fuel

#600047

[nggallery id=1504]

Never miss an issue of RC Car Action!

Subscribe today with a Digital Edition subscription or Print + Digital combo!

 

Updated: March 9, 2016 — 9:30 AM
Air Age Media ©