Hobbico AARMA Outkast 900x250
Log In

MIP Header Gasket And Lock Kit For The Losi 5IVE‑T [VIDEO]

MIP Header Gasket And Lock Kit For The Losi 5IVE‑T [VIDEO]


From MIP:

mip-header-gasket-and-lock-kit-for-the-losi-5ive%e2%80%91t-2

Header Gasket

Leaking, burned up, non-reusable header gaskets have plagued our engines for much too long, time to introduce a little MIP Magic. From searching high and low we finally narrowed our search down to some gasket material used in the dragster engine world. Tested and proven for months to stand up to heat, pressure, and the insane vibrations from our engines, be assured that MIP’s new header gasket is made to last. For the best results couple the MIP Header Gasket with MIP’s Header Lock kit part # 14350. (If header comes loose, this could result in a burned MIP gasket)

TARGET CUSTOMERS:

  • Losi 5ive-T Race Vehicles

COMPETITIVE ADVANTAGES:

  • Stop leaking headers
  • No more burned up gaskets (if header stays tight)
  • Reusable

FEATURES:

  • 100% Made in the USA!

INCLUDES:

MIP Confetti Sticker (2), MIP Header Gasket (1)

REQUIRES:

  • 10mm Hex Nut Driver / Wrench

COMPATIBILITY:

  • Losi 5ive-T

#15160 – $10.00

mip-header-gasket-and-lock-kit-for-the-losi-5ive%e2%80%91t-1
Header Lock Kit

Ask any 1/5 scale owner if they have had their header pipe come off during a run, and without a doubt we know the answer will be YES! This doesn’t happen due to lack of maintenance but rather a poor design as the bolts vibrate loose even with the application of red thread loc. As we are all aware thread loc loses its effectiveness when heat is applied, and what does an engine produce? That’s right, HEAT! Actually a constant 240°F (116°C)! This header pipe failure happened to the MIP team just one time, and we were not so impressed, so we re-engineered the bolt system that holds on the header pipe. With this oldie but goodie design you can rest assured that you will never hear the distinctive BAAAAAAHHHHHH sound that signifies your header pipe just came off. With the use of this product it is quite impossible for the bolts to loosen up as the other bolt will be pulled on by the wire subsequently tightening itself up. Welcome to next level, MIP’s Level. 100% Made and Designed in the USA.

TARGET CUSTOMERS:

  • 1/5 Scale Customers that have header pipes

COMPETITIVE ADVANTAGES:

  • Full power throughout the Race
    No more worries

FEATURES:

  • 100% Made in the USA

INCLUDES:

MIP Confetti Sticker (2), MIP Instructions Sheet (1), SHSS M5 x 25mm Cup Point Set Screw (2), M5 x 9mm Lock Washer (2), MIP Wired Header Nut (2), MIP Header Wire 2 Feet (1)

REQUIRES:

  • 2.5mm Allen Key- (Suggest #9009 MIP Hex Driver Wrench 2.5mm)
  • 10mm Open-End Wrench
  • Wire Cutters

COMPATIBILITY:

  • 1/5 5ive-T 4WD Off-Road Truck (#LOSB0019)

#14350 – $15.00

Visit MIPOnline.com
See more posts about MIP

mip-header-gasket-and-lock-kit-for-the-losi-5ive%e2%80%91t-3
rc-car-action-gear-guide

Updated: December 9, 2016 — 5:59 PM
Traxxas Mustang  600x120
Hobbico AARMA Outkast 600x120

Leave a Reply

Your email address will not be published. Required fields are marked *

Airage Media © 2017
WordPress Video Lightbox Plugin